防静电白色热控涂层的空间环境性能试验

通过在氧化锌晶格中掺入重金属离子，得到具有防静电功能的白色颜料，再以丙烯酸树脂为粘合剂制备出空间飞行器外表面用的ACR－1防静电白色热控涂层；研究了空间环境效应（包括紫外辐照，电子和质子辐照）对该热控涂层太阳吸收率的影响并与有机硅白色热控涂层进行了比较，地面模拟空间环境试验研究结果证明，ACR－1防静电白色热控涂层具有良好的空间稳定性。     

微重力下管肋式空间辐射器的整体优化分析

建立了向一重力环境下管肋式空间辐射器传热过程的数学模型，并以单质量散热量最大和热载体驱动功率最小为优化目标，对管式空间辐射器进行了优化分析。     

多机并联火箭羽流流场及其底部热环境分析

For the problem that the plume flow field structure of a multi engine parallel rocket is complicated and the bottom thermal environment is extremely harsh, which may cause the failure of the engine structural components, the plume flow field and thermal environment at different altitudes are studied through numerical simulation. The result is compared with the measured results in flight which shows that when the rocket is flying at a low altitude, the plume of the engines do not interfere with each other. As the flight altitude increases, the plumes gradually expand and begin to interfere with each other, and finally there is an obvious backflow at the bottom of the rocket. The maximum heat flux at the moment of take off is basically the same as the measured value in flight. Before the backflow occurs, the heat flux mainly consists of radiant heat, the convective heat flow increases as the flight altitude grows, but it is also much smaller than the peak heat flow at takeoff. The result has certain guiding significance for the optimal design of engine structure thermal protection.     

新型结构粘接材料对航空有机玻璃性能的影响

选用新型结构粘接材料中低温固化环氧结构胶膜J-351和改性丙烯酸酯液体胶胶黏剂SY-50s,表征胶黏剂对有机玻璃的粘接性能以及应力-溶剂银纹性能,并研究胶黏剂对有机玻璃力学性能的影响。结果表明:两种胶黏剂对有机玻璃具有良好的粘接性能,J-351抗应力溶剂银纹性能优于SY-50s;有机玻璃表面施胶后力学性能下降,与定向有机玻璃相比,浇注有机玻璃力学性能下降更为明显。通过对拉伸试样断口形貌分析发现,拉伸试样带有胶黏剂的一侧首先发生破坏。因SY-50s与有机玻璃界面结合紧密,导致带有SY-50s胶黏剂的有机玻璃力学性能下降程度较大;而J-351环氧胶膜与有机玻璃界面清晰,对有机玻璃力学性能影响相对较小。因胶黏剂对有机玻璃性能的影响,导致采用SY-50s胶黏剂粘接的试样边缘连接强度低于J-351胶黏剂粘接的试样,新型结构粘接材料J-351环氧胶膜在有机玻璃粘接中应用性能良好。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

Mg-Sc-Y三元合金的微观组织和力学性能

稀土元素作为重要的镁合金强化相元素,其多元添加产生的影响并未得到充分研究。在Mg-Sc二元系的基础上将Y作为第三元加入,制备了Mg-5Sc二元合金及Mg-5Sc-0.5Y,Mg-5Sc-1Y,Mg-5Sc-2Y,Mg-5Sc-3Y,Mg-5Sc-3.5Y(质量分数,%)5种三元合金,并通过光学显微镜(OM)、扫描电子显微镜(SEM)、X射线衍射(XRD)及室温拉伸等试验,研究了Y元素的加入对Mg-Sc二元合金微观组织和力学性能的影响。结果表明:Y元素在合金中的主要存在形式为固溶态,富集于晶界处。随着Y元素含量的提升,合金晶粒度显著减小,屈服强度和硬度大幅提升,Mg-5Sc-3.5Y的屈服强度相比Mg-5Sc提升了约50%。该强度的提升主要是由细晶强化和固溶强化引起的。     

火星表面热环境对航天器热控影响分析

火星大气对太阳辐射产生吸收和散射作用，同时还将与火星表面航天器发生对流换热。热设计时难以直接评估对流、辐射和导热三种换热对航天器的影响，从而确定主要的控温途径。在调研火星表面辐射、大气等热环境的基础上，从线性化传热系数和对流辐射比的角度对比分析了辐射、对流和导热对航天器的影响。器表辐射传热系数随光学属性和温度的变化范围为0.3～1.4W/(m2·℃)，对流传热系数随风速变化为0.2～1.5W/(m2·℃)，器内导热传热系数可控制在0.25W/(m2·℃)以下。结果表明，太阳辐射较火星表面和天空辐射而言是主要外热源，航天器表面的辐射和对流换热为两条并联换热途径，两者均可成为主要换热途径，器内导热传热是控制航天器内外隔热的主要可控因素。     

支线飞机综合飞行仿真平台设计

针对支线飞机机械操纵系统的特点,设计了由模块化的功能单元组成的综合飞行仿真平台,可以实现机械操纵系统数字仿真,在支线飞机的设计与制造中有着重要的应用价值,此平台通过改进还可用于支线飞机的试飞科目训练,从而降低试飞风险并缩短研制周期。     

CFD软件自动化验证确认云平台设计与实现

针对大型计算流体力学(CFD)软件的验证与确认,为了减少人工成本,提高软件质量和开发效率,并适应于未来高性能计算发展的要求,基于云计算思想,提出了自动化测试云平台的解决方案。该方案采用模块化的浏览器/服务器(B/S)网络架构;利用LAMP(Linux+Apache+MySQL+PHP/Python)开发工具;建立了持续集成的专业数据库;构建了涵盖可靠集群监控、复杂作业调度及大规模并行计算功能的云端环境;实现了通过便捷的网络访问,自动加载测试算例、提交集群计算、监测实时进度、自动化后处理、输出分析结果,并提供丰富的实验对比图、误差分析报表和汇总报告等;完成了对大型CFD软件的自动化验证与确认。将该方案应用于某大规模并行计算的CFD软件,验证了该解决方案的可行性与实用性。     

国产T700级碳纤维增强双马树脂基复合材料的力学性能

采用扫描电子显微镜(SEM)、反气相色谱(IGC)和X射线光电子能谱仪(XPS)对国产T700级碳纤维和东丽T700S碳纤维的表面形貌、表面能和表面化学特性进行表征,测试两种碳纤维增强双马树脂基复合材料的力学性能,考察国产碳纤维复合材料的界面黏结性能、韧性和湿热性能。结果表明:碳纤维表面特性(表面形貌、表面能和表面化学组成等)对复合材料界面黏结性能具有显著影响;国产T700级碳纤维/QY9611复合材料在室温下的界面黏结性能优于T700S/QY9611复合材料;国产T700级碳纤维/QY9611复合材料的韧性优异,冲击后压缩强度达到了国外先进复合材料IM7/5250-4的水平;经湿热处理后的层间剪切强度仍与T700S/QY9611复合材料相当,说明国产T700级碳纤维/QY9611复合材料具备良好的湿热性能。